Disclosure: As an Amazon Associate we earn from qualifying purchases at no extra cost to you.

Please note: Product availability and information are based on our research at time of writing and are subject to change. Always check Amazon for the latest details before purchasing. Reviews remain editorially independent.

Are you replacing a small vent, or do you need a separator that goes in the pipe?

Most air problems in a hot-water heating system come down to one question. If you have a small vent that leaks or sticks, you are probably replacing a point vent: a little float valve that screws into a port at the boiler or a high spot and lets trapped air out on its own. If you want something that catches air in the pipe as the water flows past, that is a separator, and it is a different job. This guide compares four point vents and one separator. We read the makers’ documents and the Amazon listings, and we have not tested any of them. If the air is a symptom of a bigger problem, such as a failing pump, our hydronic circulator pump roundup may help.

What to match

  • Thread size and type. Four of these use a 1/8 in thread, and male and female ends are not interchangeable. Look at your old vent or its port.
  • Mounting. Some vents have to stand upright. The Maid O’Mist does.
  • Pressure and temperature. Most list 150 psi and 240 F, while the Maid O’Mist lists 50 psi. Ask your technician what your system runs at.
  • Pack size. Check whether the listing is for one vent or several.

✏️ Our Take

For a like-for-like swap, match the thread first and the brand second. We read maker sheets for the Taco and the Maid O’Mist, while the Watts and HYDRO MASTER details come from their listings. The Maid O’Mist is the one with the lower pressure limit. The Webstone is a separate job, and its listing needs a close look before you order.

IN THIS GUIDE

Quick Comparison Table

Wide table: this table is wider than the page on small screens — swipe or scroll it sideways to see every column →

Pick Type Size Check before ordering Buying link
Taco 400-4 Hy-Vent Point vent 1/8 in NPT Thread on your port; male or female View on Amazon
HYDRO MASTER Brass Air Vent, ⅛ inch Point vent 1/8 in male NPT Single or pack of 2 View on Amazon
Watts FV-4M1 Point vent 1/8 in thread Thread type: confirm before ordering View on Amazon
Maid O’ Mist No. 67 Auto-Vent Point vent 1/8 in IP male 50 psi limit and vertical mounting View on Amazon
Webstone H-74003 ž-inch inline option 3/4 in Connection type; seller and delivery date View on Amazon

Point vents and one inline separator

Picks 1 to 4 are point vents. Pick 5 is an inline separator. The order is not a ranking.

1. Taco 400-4 Hy-Vent

The Hy-Vent is the classic boiler air vent: a brass float vent that screws into a port and lets air out on its own. Taco’s catalog lists the 400 as a 1/8 in NPT vent rated to 150 psi and 240 F, and says the vent cap unscrews for servicing. It suits a boiler or a high point on the baseboard loop.

Before you buy: confirm the 1/8 in thread matches your port. Retailers describe the 400-4 as a male thread, but Taco’s catalog does not say male or female. Amazon’s details table has errors (it shows a 2 in inlet), so go by the title and Taco’s catalog.

Taco

Taco 400-4 Hy-Vent Automatic Air Vent, 1/8 in NPT

Best for: A like-for-like replacement for a 1/8 in boiler or baseboard vent

Taco's Hy-Vent 400 is a brass float-type automatic air vent with a 1/8 in NPT thread, rated 150 psi and 240 F in Taco's catalog.


Pros and Cons ▾ tap to expand

2. HYDRO MASTER Brass Air Vent, ⅛ inch

A plain brass automatic air vent sold under the HYDRO MASTER name. The listing describes a 1/8 in male NPT thread and gives 150 psi and 240 F ratings. It is a good fit if you want a simple replacement vent for the same 1/8 in port.

Before you buy: check the pack size. The same listing offers a single vent and a pack of 2, so make sure the size you pick is the one you want. The brand on the listing is HYDRO MASTER, and the model number in its details table is a barcode number, not a maker part number.

HYDRO MASTER

HYDRO MASTER Brass Automatic Air Vent, 1/8 in

Best for: A plain replacement vent for a 1/8 in port

A brass automatic air vent sold under the HYDRO MASTER name, described in its Amazon listing as a 1/8 in male NPT vent rated 150 psi and 240 F.


Pros and Cons ▾ tap to expand

3. Watts FV-4M1

Watts’ FV-4 series are brass float vents for hot-water heating. The listing describes a brass body with a silicone seal and a polyethylene float, rated to 150 psi at 240 F, and says it can be taken apart for cleaning.

Before you buy: confirm the thread type on your port and on the vent before ordering.

Watts

Watts FV-4M1 Brass Automatic Air Vent, 1/8 in

Best for: A 1/8 in replacement vent once the thread is confirmed

A Watts FV-4 series brass float vent for hot-water heating.


Pros and Cons ▾ tap to expand

4. Maid O’ Mist No. 67 Auto-Vent

The No. 67 is a small float vent made for convectors, baseboard and radiant panels, where space is tight. Maid-O’-Mist’s sheet lists a vertical-mount vent with a 1/8 in IP male connection, a 50 psi pressure limit, a 240 F limit and approval for 50/50 glycol.

Before you buy: its 50 psi limit is lower than the others here, so ask your technician what pressure your system runs at. It must be mounted vertically.

Maid-O'-Mist

Maid-O’-Mist No. 67 Auto-Vent, 1/8 in IP Male

Best for: Tight spots on baseboard, convector or radiant panel loops

A small vertical-mount float vent for convectors, baseboard and radiant panels.


Pros and Cons ▾ tap to expand

5. Webstone H-74003 (ž-inch inline option)

This one is different. A separator goes in the pipe and catches air as the water moves past, and Webstone’s brochure describes a forged brass body with a removable vent head and a stainless steel coalescing medium, rated to 150 psi, with flow allowed in either side. Fitting one changes the piping, so talk it through with your heating technician first.

Before you buy: Webstone lists the H-74003 as threaded, but the Amazon title says C×C (sweat). Ask the seller to confirm the model and connection before ordering. If you need the sweat version, look for model 75003. Check the seller and delivery date.

Webstone

Webstone H-74003 Brass Air Separator, 3/4 in

Best for: An inline separator, once the connection type is confirmed

A 3/4 in brass air separator with a removable vent head and stainless steel coalescing medium, rated 150 psi in Webstone's brochure.


Pros and Cons ▾ tap to expand

Sources

Documents and Amazon listings read on 17 November 2026. Listing details are used only where attributed to the listing; Watts and HYDRO MASTER details come from their Amazon listings.

✍️ About This Review

PTR Editorial Team — Product Reviews. We compare manufacturer specifications, installation requirements, compatibility and available product documentation to help homeowners choose suitable tools and parts. How we review →